dnssec-coverage — checks future DNSKEY coverage for a zone
dnssec-coverage
[-K ]
[directory-l ]
[length-f ]
[file-d ]
[DNSKEY TTL-m ]
[max TTL-r ]
[interval-c ]
[compilezone path-k]
[-z]
[zone...]
dnssec-coverage verifies that the DNSSEC keys for a given zone or a set of zones have timing metadata set properly to ensure no future lapses in DNSSEC coverage.
If zone is specified, then keys found in
the key repository matching that zone are scanned, and an ordered
list is generated of the events scheduled for that key (i.e.,
publication, activation, inactivation, deletion). The list of
events is walked in order of occurrence. Warnings are generated
if any event is scheduled which could cause the zone to enter a
state in which validation failures might occur: for example, if
the number of published or active keys for a given algorithm drops
to zero, or if a key is deleted from the zone too soon after a new
key is rolled, and cached data signed by the prior key has not had
time to expire from resolver caches.
If zone is not specified, then all keys in the
key repository will be scanned, and all zones for which there are
keys will be analyzed. (Note: This method of reporting is only
accurate if all the zones that have keys in a given repository
share the same TTL parameters.)
directorySets the directory in which keys can be found. Defaults to the current working directory.
file
If a file is specified, then the zone is
read from that file; the largest TTL and the DNSKEY TTL are
determined directly from the zone data, and the
-m and -d options do
not need to be specified on the command line.
duration
The length of time to check for DNSSEC coverage. Key events
scheduled further into the future than duration
will be ignored, and assumed to be correct.
The value of duration can be set in seconds,
or in larger units of time by adding a suffix: 'mi' for minutes,
'h' for hours, 'd' for days, 'w' for weeks, 'mo' for months,
'y' for years.
maximum TTLSets the value to be used as the maximum TTL for the zone or zones being analyzed when determining whether there is a possibility of validation failure. When a zone-signing key is deactivated, there must be enough time for the record in the zone with the longest TTL to have expired from resolver caches before that key can be purged from the DNSKEY RRset. If that condition does not apply, a warning will be generated.
The length of the TTL can be set in seconds, or in larger units of time by adding a suffix: 'mi' for minutes, 'h' for hours, 'd' for days, 'w' for weeks, 'mo' for months, 'y' for years.
This option is not necessary if the -f has
been used to specify a zone file. If -f has
been specified, this option may still be used; it will override
the value found in the file.
If this option is not used and the maximum TTL cannot be retrieved from a zone file, a warning is generated and a default value of 1 week is used.
DNSKEY TTLSets the value to be used as the DNSKEY TTL for the zone or zones being analyzed when determining whether there is a possibility of validation failure. When a key is rolled (that is, replaced with a new key), there must be enough time for the old DNSKEY RRset to have expired from resolver caches before the new key is activated and begins generating signatures. If that condition does not apply, a warning will be generated.
The length of the TTL can be set in seconds, or in larger units of time by adding a suffix: 'mi' for minutes, 'h' for hours, 'd' for days, 'w' for weeks, 'mo' for months, 'y' for years.
This option is not necessary if -f has
been used to specify a zone file from which the TTL
of the DNSKEY RRset can be read, or if a default key TTL was
set using ith the -L to
dnssec-keygen. If either of those is true,
this option may still be used; it will override the values
found in the zone file or the key file.
If this option is not used and the key TTL cannot be retrieved from the zone file or the key file, then a warning is generated and a default value of 1 day is used.
resign interval
Sets the value to be used as the resign interval for the zone
or zones being analyzed when determining whether there is a
possibility of validation failure. This value defaults to
22.5 days, which is also the default in
named. However, if it has been changed
by the sig-validity-interval option in
named.conf, then it should also be
changed here.
The length of the interval can be set in seconds, or in larger units of time by adding a suffix: 'mi' for minutes, 'h' for hours, 'd' for days, 'w' for weeks, 'mo' for months, 'y' for years.
Only check KSK coverage; ignore ZSK events. Cannot be
used with -z.
Only check ZSK coverage; ignore KSK events. Cannot be
used with -k.
compilezone pathSpecifies a path to a named-compilezone binary. Used for testing.
BIND 9.11.4rc1 (Extended Support Version)